View LXR7-RW30_6417936.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

features and benefts ? uniform image enabling tight beam control in mr-16 and spot lighting applications ? specifed, targeted and tested hot, at real world operating temperatures: t j = 85c to ensure in application performance ? high flux density with over 1200 hot lumens available from a 3x3 mm led area enables reduced emitter counts and compact fxture designs ? uniform intensity and color across source with 70, 80 and 90 cri minimum ? freedom from binning delivers color consistency within a single 3 or 5-step macadam ellipse ? 11.2v and 5.6v packages put high performance within reach with high effciency and low cost drivers ? exceeds energy star ? lumen maintenance requirements. key applications ? outdoor ? high bay and low bay ? downlights ? lamps ? indoor area lighting ? spotlights luxeon m ds103 ?2013 philips lumileds lighting company. luxeon m high flux density and effcacy introduction luxeon ? m emitters are illumination grade leds designed to enable indoor, outdoor and industrial applications which are optimized either for high effciency or low cost. with freedom from binning and leading performance, luxeon m emitters deliver high effcacy and high fux density from a uniform source with tight correlated color temperature control.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. i table of contents general information 2 product nomenclature 2 average lumen maintenance characteristics 3 environmental compliance 3 product selection 4 optical and electrical characteristics 6 absolute maximum ratings 7 jedec moisture sensitivity 7 refow soldering characteristics 8 mechanical dimensions 9 pad confguration 9 solder pad design 10 relative spectral distribution vs wavelength characteristics 11 typical light output characteristics 13 typical light output characteristics 14 forward current characteristics 15 typical radiation patterns 16 emitter pocket tape packaging 17 emitter reel packaging 18 product binning and labeling 19 luminous flux bins 20 radiometric power bins 20 luxeon m color bin defnition 21
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 2 general information product nomenclature luxeon m emitters are specifed and binned hot under conditions comparable to those found in real-world lighting products. the part number designation is explained as follows: l x r a - b c d e - f g h j where: a designates minimum cri (7 = 70, 8 = 80, 9 = 90, 0 = royal blue) b is s for serially connected product with voltage less than 12v; r for series-parallel collected product with voltage less than 6v. c designates color designation (w = white, r = royal blue) d, e designates cct (27 = 2700k, 30 = 3000k, 35 = 3500k, 40 = 4000k, 50 = 5000k, 57 = 5700k, 00 = royal blue) fghj minimum fux lumen (optional) the test conditions for 12v luxeon m lxra-scde-fghj are 700ma dc with junction temperature 85c. the test condition for 6v luxeon m lxra-rcde-fghj are 1400ma dc with junction temperature 85c. therefore luxeon m 12v products tested and binned at 700 ma follow the part numbering scheme: l x r 7 - s w 3 0 - x x x x l x r 7 - s w 4 0 - x x x x l x r 7 - s w 5 0 - x x x x l x r 7 - s w 5 7 - x x x x l x r 7 - s w 6 5 - x x x x l x r 8 - s w 2 7 - x x x x l x r 8 - s w 3 0 - x x x x l x r 8 - s w 3 5 - x x x x l x r 8 - s w 4 0 - x x x x l x r 8 - s w 5 0 - x x x x l x r 9 - s w 2 7 - x x x x l x r 9 - s w 3 0 - x x x x l x r 0 - s r 0 0 - x x x x
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 3 luxeon m 6v products tested and binned at 1400 ma follow the part numbering scheme: l x r 7 - r w 3 0 - x x x x l x r 7 - r w 4 0 - x x x x l x r 7 - r w 5 0 - x x x x l x r 7 - r w 5 7 - x x x x l x r 7 - r w 6 5 - x x x x l x r 8 - r w 2 7 - x x x x l x r 8 - r w 3 0 - x x x x l x r 8 - r w 3 5 - x x x x l x r 8 - r w 4 0 - x x x x l x r 8 - r w 5 0 - x x x x l x r 9 - r w 2 7 - x x x x l x r 9 - r w 3 0 - x x x x l x r 0 - r r 0 0 - x x x x average lumen maintenance characteristics lumen maintenance for solid-state lighting devices (leds) is typically defned in terms of the percentage of initial light output remaining after a specifed period of time. philips lumileds projects that luxeon m products will deliver, on average, 70% lumen maintenance (l70) at 50,000 hours of operation at a forward current of up to 700 ma for lxrx-sxxx and 1400 ma for lxrx-rxxx. this projection is based on constant current operation with junction temperature maintained at or below 135c. this performance is based on philips lumileds historical data from tests run on similar material systems, and internal lm80 and reliability testing. observation of design limits included in this data sheet is required in order to achieve this projected lumen maintenance. environmental compliance philips lumileds is committed to providing environmentally friendly products to the solid-state lighting market. luxeon m is compliant to the european union directives on the restriction of hazardous substances in electronic equipment, namely the rohs directive. philips lumileds will not intentionally add the following restricted materials to the luxeon m lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb) or polybrominated diphenyl ethers (pbde).
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 4 product selection product selection guide for luxeon m 12v white junction temperature = 85c table 1. performance at test current nominal cct part number minimum cri minimum luminous flux (lm) typical luminous flux (lm) 3000k lxr7-sw30 70 840 905 4000k lxr7-sw40 70 900 980 5000k lxr7-sw50 70 900 980 5700k lxr7-sw57 70 900 1000 6500k lxr7-sw65 70 900 1000 2700k lxr8-sw27 80 680 760 3000k lxr8-sw30 80 710 800 3500k lxr8-sw35 80 745 860 4000k lxr8-sw40 80 780 905 5000k lxr8-sw50 80 800 905 2700k lxr9-sw27 90 570 610 3000k lxr9-sw30 90 580 620 notes for table 1: 1. philips lumileds maintains a tolerance of 6.5% on fux measurements. 2. test current is 700 ma for all lxrx-swxx products. product selection guide for luxeon m 12v royal blue junction temperature = 85c table 2. performance at test current color part number minimum radiometric power (mw) typical radiometric power (mw) typical radiant effcacy (%) royal blue lxr0-sr00 4000 4200 53.6 note for table 2: 1. philips lumileds maintains a tolerance of 6.5% on fux measurements. 2. test current is 700 ma for lxr0-sr00 products.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 5 product selection guide for luxeon m 6v white junction temperature = 85c table 3. performance at test current nominal cct part number minimum cri minimum luminous flux (lm) typical luminous flux (lm) 3000k LXR7-RW30 70 840 905 4000k lxr7-rw40 70 900 980 5000k lxr7-rw50 70 900 980 5700k lxr7-rw57 70 900 1000 6500k lxr7-rw65 70 900 1000 2700k lxr8-rw27 80 680 760 3000k lxr8-rw30 80 710 800 3500k lxr8-rw35 80 745 860 4000k lxr8-rw40 80 780 905 5000k lxr8-rw50 80 800 905 2700k lxr9-rw27 90 570 610 3000k lxr9-rw30 90 580 620 notes for table 3: 1. philips lumileds maintains a tolerance of 6.5% on fux measurements. 2. test current is 1400 ma for all lxrx-rwxx products. product selection guide for luxeon m 6v royal blue junction temperature = 85c table 4. performance at test current color part number minimum radiometric power (mw) typical radiometric power (mw) typical radiant effcacy (%) royal blue lxr0-rr00 4000 4200 53.6 note for table 4: 1. philips lumileds maintains a tolerance of 6.5% on fux measurements. 2. test current is 1400 ma for lxr0-rr00 products.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 6 optical and electrical characteristics luxeon m white at test current [1] , junction temperature = 85c table 5. nominal cct (k) part number color temperature [2] cct typical (k) typ total included angle [2] (degrees) u 0 90v typ viewing angle [3] (degrees) 2 u 1/2 2700 lxr8-sw27, lxr8-rw27 lxr9-sw27, lxr9-rw27 2725 2725 140 140 120 120 3000 lxr7-sw30, LXR7-RW30 lxr8-sw30, lxr8-rw30 lxr9-sw30, lxr9-rw30 3045 3045 3045 140 140 140 120 120 120 3500 lxr8-sw35, lxr8-rw35 3465 140 120 4000 lxr7-sw40, lxr7-rw40 lxr8-sw40, lxr8-rw40 3985 3985 140 140 120 120 5000 lxr7-sw50, lxr7-rw50 lxr8-sw50, lxr8-rw50 5028 5028 140 140 120 120 5700 lxr7-sw57, lxr7-rw57 5665 140 120 6500 lxr7-sw65, lxr7-rw65 6530 140 120 notes for table 5: 1. test current is 700 ma for lxrx-swxx and 1400 ma for lxrx-rwxx products. 2. total included angle at which 90% of total luminous fux is captured. 3. viewing angle is the off axis angle from lamp centerline where the luminous intensity is ? of the peak value. luxeon m royal blue at test current [1] , junction temperature = 85c table 6. peak wavelength, p [2] typical spectral half-width (nm) [3] d 1/2 typ temperature coeffcient of peak wavelength (nm/c) d d / d t j typ total included angle (degrees) [4] u 90v typical viewing angle (degrees) [5] 2 u 1/2 color minimum typical maximum royal blue 445.0 nm 447.5nm 460.0nm 22 0.05 140 150 notes for table 6: 1. test current is 700 ma for lxr0-sr00 and 1400 ma for lxr0-rr00. 2. royal blue product is binned by radiometric power and peak wavelength rather than photometric lumens. 3. spectral half-width is 1/2 of the peak intensity. 4. total included angle at which 90% of total radiometric power is captured. 5. viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 7 electrical characteristics for luxeon m at test current [1] , junction temperature = 85c for all ccts and royal blue table 7. part number forward voltage v f [1, 2] (v) i f = 700 ma typical temperature coeffcient of forward voltage [3] (mv/c) d v f / d t j typical thermal resistance junction to thermal pad (c/w) r u j-c minimum typical maximum lxrx-sxxx 10.5 11.2 12 -5.5 1.25 lxrx-rxxx 5.44 5.6 5.72 -5.5 1.25 notes for table 7: 1. test current is 700 ma for lxrx-sxxx and 1400 ma for lxrx-rxxx products. 2. philips lumileds maintains a tolerance of 0.5% on forward voltage measurements. 3. measured between t j = 25c and t j = 135c. absolute maximum ratings table 8. parameter maximum performance dc forward current (ma) [1], [2] 1050 ma for lxrx-sxxx; 2100 ma for lxrx-rxxx peak pulsed forward current [1], [3] 1200 ma for lxrx-sxxx; 2400 ma for lxrx-rxxx esd sensitivity 8000v human body model (hbm) class 3b jesd22-a114-e < 400v machine model (mm) class b jesd22-a115-b led junction temperature [1] 135c operating case temperature at current -40c - 120c @ 700 ma for lxrx-sxxx -40c - 120c @1400 ma for lxrx-rxxx storage temperature -40c - 120c lead soldering temperature jedec 020c 260c allowable refow cycles 3 autoclave conditions 121c at 2 atm 100% relative humidity for 96 hours maximum reverse voltage (v r ) luxeon m leds are not designed to be driven in reverse bias notes for table 8: 1. proper current derating must be observed to maintain junction temperature below the maximum. 2. residual periodic variations due to power conversion from alternating current (ac) to direct current (dc), also called ripple, with frequencies 100hz and amplitude 1200 ma for lxrx-sxxx and amplitude 2400 ma for lxrx-rxxx are acceptable, assuming the average current throughout each cycle does not exceed 1050 ma for lxrx-sxxx and 2100 ma for lxrx-rxxx. 3. pulsed operation with a peak drive current of 1200 ma for lxrx-sxxx and peak drive current of 2400 ma for lxrx-rxxx is acceptable if the pulse on time is 5ms per cycle and the duty cycle is 50%. jedec moisture sensitivity table 9. level soak requirements floor life standard time conditions time conditions 1 unlimited [ 30c / 85% rh 168 hrs. + 5 / -0 hrs. 85c / 85% rh
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 8 refow soldering characteristics table 10. profle feature lead free assembly average ramp-up rate (ts max to t p ) 3c / second max preheat temperature min (ts min ) 150c preheat temperature max (ts max ) 200c preheat time (ts min to ts max ) 60 - 180 seconds time maintained above temperature t l 217c time maintained above time (t l ) 60 - 150 seconds peak / classifcation temperature (t p ) 260c time within 5c of actual peak temperature (t p ) 20 - 40 seconds ramp-down rate 6c / second max time 25c to peak temperature 8 minutes max note for table 10: 1. all temperatures refer to the application printed circuit board (pcb), measured on the surface adjacent to the package body. temperature profle for table 8.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 9 mechanical dimensions 7.000.12 7.000.12 6.40 0.06 3.140.10 3.140.10 3.500.15 3.500.15 2.160.06 3.760.06 0.300.06 0.500.06 0.37 3.97 3.530.06 3.140.06 3.140.06 frame laser mark area (isolated) heat pad (isolated) anode cathode 3x fiducial located front side shown for reference only c l 3.750.12 0.560.08 r0.200.04 c l figure 2. package outline drawing. notes for figure 2: 1. do not handle the device by the lens. excessive force on the lens may damage the lens itself or the interior of the device. 2. all dimensions are in millimeters. 3. drawings not to scale. 4. the thermal pad is electrically isolated from the anode and cathode contact pads. pad confguration note for figure 3: 1. the thermal pad is electrically isolated from the anode and cathode contact pads. cathode thermal pad anode laser marking fiducial ceramic frame tvs silicone dome ceramic substrate with led chip array figure 3. pad confguration.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 10 solder pad design figure 4. recommended luxeon m footprint design for metal core pcb. all dimensions are in millimeters. notes for figure 4: 1. the luxeon m application brief provides extensive details for this layout. 2. printed circuit board layout fles (.dwg) are available at www. philipslumileds.com and www.philipslumileds.cn.com
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 11 relative spectral distribution vs wavelength characteristics lxr7-xwxx (white) at test current, junction temperature = 85c lxr8-xwxx (white) at test current, junction temperature = 85c lxr7-x w30 lxr7-x w40 lxr7-x w50 lxr7-x w57 lxr7-x w65 figure 5. color spectrum of lxr7-xwxx emitter, integrated measurement. x x x x x figure 6. color spectrum of lxr8-xwxx emitter, integrated measurement.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 12 lxr9-xwxx (white) at test current, junction temperature = 85c lxr0-xr00 (royal blue) at test current, junction temperature = 85c x x figure 7. color spectrum of lxr9-xwxx emitter, integrated measurement. x figure 8. color spectrum of lxr0-xr00 emitter, integrated measurement.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 13 typical light output characteristics typical relative light output characteristics over temperature at test current of 700/1400 ma for lxrx-xwxx (white) and lxr0-xr00 (royal blue) typical relative luminous flux vs forward current, junction temperature = 85c for lxrx-swxx (white) and lxr0-sr00 (royal blue) figure 9. relative light output vs. junction temperature. figure 10. relative light output vs. forward current (12v).
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 14 typical light output characteristics typical relative luminous flux vs forward current, junction temperature = 85c for lxrx-rwxx (white) and lxr0-rr00 (royal blue) figure 11. relative light output vs. forward current (6v).
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 15 forward current characteristics typical forward current vs forward voltage, junction temperature = 85c for lxrx-swxx (white) and lxr0-sr00 (royal blue) typical forward current vs forward voltage, junction temperature = 85c for lxrx-rwxx (white) and lxr0-rr00 (royal blue) figure 12. forward current vs. forward voltage (12v). figure 13. forward current vs. forward voltage (6v).
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 16 typical radiation patterns typical spatial radiation pattern for lxrx-xwxx (white) and lxr0-xr00 (royal blue) typical polar radiation pattern for lxrx-xwxx (white) and lxr0-xr00 (royal blue) figure 14. typical representative spatial radiation pattern. figure 15. typical polar radiation pattern.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 17 emitter pocket tape packaging direction of feed 4.00mm index hole pitch 12.00mm pocket pitch 1.50 1.50 2.00 1.75 7.50 4.59 1.59 4.99 b b 7.35 sq. 4.11 0.38 4.49 4.99 5.35 8 section b-b scale 2 : 1 16.00 4 f -loaded pockets- 500 e -leader- 50 empty pockets -tape end- 30 empty pockets direction of feed detail e scale 4 : 1 -device orientation- non-fiducial corner locatedas shown detail f scale 4 : 1 figure 16. emitter pocket tape packaging.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 18 emitter reel packaging 13.00mm arbor hole diameter 330.00 reel diameter direction of feed carrier tape cover tape tape reel 20.8mm outside width 16.4mm inside width figure 17. emitter reel packaging.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 19 product binning and labeling purpose of product binning in the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. for this reason, philips lumileds bins the led components for luminous fux, color, and forward voltage (v f ). decoding product bin labeling reels with luxeon m white emitters are labeled with a four digit alphanumeric code (cat code) following the format below. all emitters packaged within a reel are of the same 4-variable bin combination. for lxrx-xwxx, reels of emitters are labeled with a four digit alphanumeric cat code following the format below. abcd a = luminous fux bin (see table 9) b = color or cct indication (2 for 5700k, 3 for 5000k, 5 for 4000k, 6 for 3500k, 7 for 3000k, and 8 for 2700k) c = color consistency (5 for within 5 sdcm ellipse, 3 for within 3scdm ellipse). detailed defnitions for these color bins can be found in table 11. d = v f bin (f,g,h) reels with luxeon m royal blue emitters are labeled with a three digit alphanumeric cat code following the format below. all emitters packaged within a reel are of the same 4-variable bin combination. abc a = radiometric power bin (see table 10) b = peak wavelength bin (see table 12) c = v f bin (f,g,h)
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 20 luminous flux bins table 11 lists the standard photometric luminous fux bins for luxeon m white emitters (lxrx-xwxx). test conditions for lxrx-swxx are 700 ma and junction temperature 85oc. test conditions for lxrx-rwxx are 1400 ma and junction temperature 85oc. although several bins are outlined, product availability in a particular bin varies by production run and by product performance. table 11. luminous flux bins for white bin code minimum photometric flux (lm) maximum photometric flux (lm) j 510 550 k 550 590 l 590 630 m 630 680 n 680 730 p 730 780 q 780 840 r 840 900 s 900 970 t 970 1040 u 1040 1120 v 1120 1200 radiometric power bins table 12 lists the standard radiometric fux bins for luxeon m royal blue emitters lxr0-sr00 and lxr0-rr00. test conditions for lxr0-sr00 are 700ma and junction temperature 85oc. test conditions for lxr0-rr00 are 1400ma and junction temperature 85oc. table 12. radiometric power bins for royal blue bin code minimum radiometric flux (mw) maximum radiometric flux (mw) a 4000 4200 b 4200 4400 c 4400 4600 d 4600 4800 e 4800 5000
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 21 luxeon m color bin defnition luxeon m 3- and 5-step macadam ellipse white color bin defnition for lxrx-swxx and lxrx-rwxx peak wavelength bin defnition for lxr0-sr00 and lxr0-rr00 table 14. peak wavelength bin structure for royal blue bin code minimum peak wavelength (nm) maximum peak wavelength (nm) 4 445 450 5 450 455 6 455 460 table 13. luxeon m color bin defnitions part number nominal ansi cct color space center point (cx, cy) major axis, a minor axis, b ellipse rotation angle (degrees) lxr7-sw30, LXR7-RW30 3000k single 5-step macadam ellipse 0.4338, 0.4030 0.01390 0.00680 53.22 lxr7-sw40, lxr7-rw40 4000k single 5-step macadam ellipse 0.3818, 0.3797 0.01565 0.00670 53.72 lxr7-sw50, lxr7-rw50 5000k single 5-step macadam ellipse 0.3447, 0.3553 0.01370 0.00590 59.62 lxr7-sw57, lxr7-rw57 5700k single 5-step macadam ellipse 0.3287, 0.3417 0.01243 0.00533 59.09 lxr7-sw65, lxr7-rw65 6500k single 5-step macadam ellipse 0.3123, 0.3282 0.01115 0.00475 58.57 lxr8-sw27, lxr8-rw27 lxr9-sw27, lxr9-rw27 2700k single 3-step macadam ellipse 0.4578, 0.4101 0.00810 0.00420 53.70 lxr8-sw30, lxr8-rw30 lxr9-sw30, lxr9-rw30 3000k single 3-step macadam ellipse 0.4338, 0.4030 0.00834 0.00408 53.22 lxr8-sw35, lxr8-rw35 3500k single 3-step macadam ellipse 0.4073, 0.3917 0.00927 0.00414 54.00 lxr8-sw40, lxr8-rw40 4000k single 3-step macadam ellipse 0.3818, 0.3797 0.00939 0.00402 53.72 lxr8-sw50, lxr8-rw50 5000k single 3-step macadam ellipse 0.3447, 0.3553 0.00822 0.00354 59.62 notes for table 13: 1. philips lumileds maintains a tester tolerance of 0.005 on x, y color coordinates. 2. tested at 700 ma d.c. and junction temperature = 85c.
luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. 22 forward voltage bins tables 15 and 16 list minimum and maximum vf bin values per emitter. although several bins are outlined, product availability in a particular bin varies by production run and by product performance. table 15. forward voltage bins for lxrx-swxx and lxr0-sr00 bin code minimum forward voltage (v) maximum forward voltage (v) f 10.5 11.0 g 11.0 11.5 h 11.5 12.0 table 16. forward voltage bins for lxrx-rwxx and lxr0-rr00 bin code minimum forward voltage (v) maximum forward voltage (v) f 5.25 5.50 g 5.50 5.75 h 5.75 6.00
company information philips lumileds is a leading provider of leds for everyday lighting applications. the companys records for light output, effcacy and thermal management are direct results of the ongoing commitment to advancing solid-state lighting technology and enabling lighting solutions that are more environmentally friendly, help reduce co2 emissions and reduce the need for power plant expansion. philips lumileds luxeon ? leds are enabling never before possible applications in outdoor lighting, shop lighting, home lighting, digital imaging, display and automotive lighting. philips lumileds is a fully integrated supplier, producing core led material in all three base colors, (red, green, blue) and white. philips lumileds has r&d centers in san jose, california and in the netherlands, and production capabilities in san jose, singapore and penang, malaysia. founded in 1999, philips lumileds is the high fux led technology leader and is dedicated to bridging the gap between solid-state technology and the lighting world. more information about the companys luxeon led products and solid-state lighting technologies can be found at www philipslumileds com. luxeon m datasheet ds103 20130418 ?2013 philips lumileds lighting company. all rights reserved. luxeon is a registered trademark of the philips lumileds lighting company in the united states and other countries. www philipslumileds com www philipslumileds cn com philips lumileds lighting company shall not be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. although philips lumileds lighting company has attempted to provide the most accurate information and data, the materials and services information and data are provided as is and philips lumileds lighting company neither warranties, nor guarantees the contents and correctness of the provided information and data. philips lumileds lighting company reserves the right to make changes without notice. you as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data.

▲Up To Search▲

Price & Availability of LXR7-RW30

	To Download LXR7-RW30 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .